 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| TECHNICAL DATA Quad Single Supply Comparator The IL339 consists of four independent precision voltage comparators with an offset voltage specification as low as 2.0 mV max for four comparators which were designed specifically to operate from a single power supply over a wide range of voltages. Application areas include limit comparators, simple analog to digital converters; pulse, squarewave and time delay generators; wide range VCO; MOS clock timers; multivibrators and high voltage digital logic gates. * Single or Split Supply Operation * Low Input Bias Current * Low Input Offset Current * Input Common Mode Voltage Range to Gnd * Low Output Saturation Voltage * TTL and CMOS Compatible IL339 ORDERING INFORMATION IL339N Plastic IL339D SOIC TA = 0 to 70 C for all packages. LOGIC DIAGRAM PIN ASSIGNMENT PIN 3 = VCC PIN 12 = GND 1 IL339 MAXIMUM RATINGS* Symbol VCC Parameter Power Supply Voltages Single Supply Split Supplies VIDR VICR ISC IIN TJ Tstg TL PD Input Differential Voltage Range Input Common Mode Voltage Range (1) Output Short Circuit to Ground Input Current, per pin (2) Junction Temperature Plastic Packages Storage Temperature Lead Temperature, 1mm from Case for 10 Seconds Power Dissipation @TA=25C Plastic Package Derate above 25C 150 -65 to +150 260 1.0 8.0 C C C W mW/C 36 18 36 -0.3 to VCC Continuous 50 mA V V V Value Unit * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the Recommended Operating Conditions. Notes: 1. Split Power Supplies. 2. VIN<-0.3V. This input current will only exist when voltage at any of the input leads is driven negative. RECOMMENDED OPERATING CONDITIONS Symbol VCC TA DC Supply Voltage Operating Temperature, All Package Types Parameter Min 2.5 or 5.0 0 Max 15 or 30 +70 Unit V C This device contains protection circuitry to guard against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high-impedance circuit. For proper operation, VIN and VOUT should be constrained to the range GND(VIN or VOUT)VCC. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either GND or VCC). Unused outputs must be left open. 2 IL339 DC ELECTRICAL CHARACTERISTICS(TA=0 to +70C) Guaranteed Limit Symbol VIO Parameter Input Offset Voltage Test Conditions V0=1.4V VCC=5.0-30V;RS100 VICR=0V - (VCC-1.5)V V0=1.4V VCC=5.0-30V VICR=0V - (VCC-1.5)V V0=1.4V VCC=5.0-30V VICR=0V - (VCC-1.5)V VCC=5.0-30V RL=,VCC=5.0 RL=,VCC=30V AVOL t1 Voltage Gain Large Signal Response Time Response Time Output Sink Current Saturation Voltage Output Leakage Current VCC=15V, RL=15K VIN=TTL Logic Swing, Vref=1.4V, VCC=5.0V, RL=5.1K, VRL=5.0V VCC=5.0V, RL=5.1K, VRL=5.0V VI(-)=1.0V, VI(+)=0V, V01.5V, VCC=5.0V VI(-)=1.0V, VI(+)=0V, Isink4.0mA, VCC=5.0V VI(+)=1.0V, VI(-)=0V, V0=5.0V V0=30V All VINGND or V-Supply (if used) Min Typ Max 9.0 Unit mV IIB Input Bias Current - 400 nA IIO Input Offset Current - 150 nA VICR ICC Input Common Mode Voltage Range Supply Current 0 200* 300* VCC2.0V 2.0* 2.5* - V mA V/mV ns t2 Isink Vsat IOL 6.0* - 1.3* - 700 s mA mV nA 0.1* 1000 VCC* V VIDR *=@25C Differential Input Voltage Range 3 IL339 TYPICAL PERFORMANCE CHARACTERISTICS (VCC=1.5V, TA=+25C, (each comporator)) Figure 1. Normalized Input Offset Voltage Figure 2. Input Bias Current Figure 3. Output Sink Current versus Output Saturation Voltage 4 |
Price & Availability of IL339
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |